1969-72 Chevelle El Camino Tilt Floor Shift Steering Column with id.CLASSIC Ignition - Paintable Steel
This retrofit column is designed to fit your Chevelle El Camino and does NOT require modification to your original vehicle to install. Simply remove your old column, saving your original under dash mount and floor mount. Using an ididit installation kit, install your new steering column in place of the old. Using an adaptor, add an aftermarket wheel and the gripping surface of the new wheel will be in the same location as the original. Please note: the 1969-72 column does not have the provision needed for the OEM Neutral Safety Switch or indicator. An alternate method must be used. The ignition is excluded on 1969 & 70 GTO. Call ididit to find out why.
|Kit Type||DELUXE KIT - ORIGINAL HARNESS||DELUXE KIT - AFTERMARKET HARNESS|
|Contents||Coupler/Shaft/Rag Joint/Flasher Kit||Coupler/Shaft/Rag Joint|
|Gearbox Input Shaft||Manual 3/4"-30||Manual 3/4"-36||Power 13/16"-36||Manual 3/4"-30||Manual 3/4"-36||Power 13/16"-36|
|1967-68||See AFTERMARKET HARNESS part numbers||3006007000||3006008000||3006009000|
|1969-72**||See AFTERMARKET HARNESS part numbers||3011007000||3011008000||3011009000|
|Kit Type||ECONO KIT - ORIGINAL HARNESS||ECONO KIT - AFTERMARKET HARNESS|
|Contents||Coupler/Flasher Kit||Coupler Only|
* Power assisted manual gear boxes were used. Please refer to manual shaft sizes.
** 1969-72 kit contains U-Joint, Rag Joint and Collapsible Intermediate Shaft only
1964-72 Chevelle/El Camino/GTO - Tilt Floor Shift - Installation Kits
This kit includes all the necessary parts you will need to install the column to the gearbox. All you need to know is the diameter of the gearbox input shaft and the number of splines.
We had the builder on a budget in mind when we designed this kit. The original joint and intermediate shaft are used. The shaft will need to be cut and modified to match the 3/4" DD coupler. Due to age, the original rag joint may be worn so please double check to make sure it is in good condition. ididit, inc. always recommends replacing the rag joint.
For vehicles with an original factory harness, a 4-way flasher kit is included in your installation kit. This 4-way flasher kit will not only add safety to your vehicle, but will also convert your original wiring harness to the 3 7/8" plug found on your ididit column. (Only neccessary for 1964-66.)
Many aftermarket wiring companies offer replacement harnesses that incorporate a 4-way flasher unit as well as the flat 3 7/8" plug. If you are using one of these harnesses, a 4-way flasher kit is not necessary.
Upgrade Your Ignition
Forget the key and go keyless with id.PUSH. Replace id.CLASSIC with id.PUSH at no additional cost. Add Part # 1000000063 when ordering your column.
Secure your ride and upgrade your ignition to id.PUSH+ for only $540. Add Part # 1000000065 when ordering your column.
Get the most elite keyless system on the market with id.TOUCH. An easy upgrade to your ignition for only $740. Add Part # 1000000071 when ordering your column.
- ididit LLC
- 1969 Chevrolet Chevelle
- 1969 Chevrolet El Camino
- 1970 Chevrolet Chevelle
- 1970 Chevrolet El Camino
- 1971 Chevrolet Chevelle
- 1971 Chevrolet El Camino
- 1972 Chevrolet Chevelle
- 1972 Chevrolet El Camino
- 1" 48
- 8-Position Tilt
- 2 in
- 2 in
- 69 to '94 GM Passenger Car
- Floor Shift
- GM 3 7/8" + GM 4 1/4"
- Manual and Auto
- Item Requires Shipping
- 14.2 lbs.
- W8.2500” x H5.7500” x L45.5000”